联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
耐热输送带工作效率
耐热输送带工作效率
Working efficiency of heat resistant conveyer belt
1、输送带的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对托辊槽角的要求应根据运输机的设计规定,合理选取。
1. The relationship between the diameter of the transmission roller and the cloth layer of the conveyer belt, the matching of the transmission roller, the reformed roller and the demand for the angle of the rollers should be reasonably selected according to the design regulations of the conveyer.
2、给料方向应顺输送带的运行方向，为减小物料下落时对输送带的冲击应采溜槽，减小物料落差距离；输送带受料段，应缩短托辊间距和采用缓冲托辊为漏料，输送带顺应采用柔软适度的挡料板，以免档料板过硬，刮破输送带的带面。
2. The direction of the feeding direction should be followed by the running direction of the conveyer belt. In order to reduce the impact of the material on the conveyor belt, the chute should be mined and the drop distance of the material is reduced. The conveying belt should shorten the spacing of the roller and use the cushion roller as the leaky material, and the conveyer belt should be flexible and appropriate, so as to avoid the gear plate to be perfect and scrape the conveyer belt. The surface of the belt.
3、防止输送带负荷启动。
3, prevent the load of conveyor belt starting.
4、输送带发生跑偏，应及时采取措施纠正。
4, belt deviation occurs, should take timely measures to correct.
5、不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
5, the conveyor belts of different types and specifications should not be used together, and the joints should be glued.
6、输送带的类型、结构、规格、层数应根据使用条件合理选用。
6, the type, structure, specification and number of layers should be selected according to the use conditions.
7、输送带运行速度一般不宜大于2.5m/s，块度大，磨损性大的物料和使用固定梨的卸料装置应尽量采用低速。
7, the conveyor belt generally should not run faster than 2.5m/s, large size, wear material and the use of fixed pear unloading device should be used as low as possible.
8、输送机在使用时，如有托辊缺少，应及时添加及修好；托辊被物料覆盖，造成回转不灵，防止漏料卡于滚筒与胶带之间，注意输送带活动部分的润滑，但不得油污输送带。
8, when the conveyor is used, if the roller is missing, it should be added and repaired in time; the roller is covered by the material, which causes no turning, prevents the leakage between the roller and the tape, and pays attention to the lubrication of the active part of the conveyer belt, but not the oil conveyer belt.
9、避免输送带遭受机架，支柱或块状物料的阻滞，防止碰破扯裂，发现输送带局部破损时，应用人造棉及时修补，以免扩大。
9, avoid the conveyor belt from the block, support or block material block, prevent breaking and tear, and find that when the conveyor belt is partially damaged, artificial cotton can be repaired in time so as not to expand.
Working efficiency of heat resistant conveyer belt
1、输送带的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对托辊槽角的要求应根据运输机的设计规定,合理选取。
1. The relationship between the diameter of the transmission roller and the cloth layer of the conveyer belt, the matching of the transmission roller, the reformed roller and the demand for the angle of the rollers should be reasonably selected according to the design regulations of the conveyer.
2、给料方向应顺输送带的运行方向，为减小物料下落时对输送带的冲击应采溜槽，减小物料落差距离；输送带受料段，应缩短托辊间距和采用缓冲托辊为漏料，输送带顺应采用柔软适度的挡料板，以免档料板过硬，刮破输送带的带面。
2. The direction of the feeding direction should be followed by the running direction of the conveyer belt. In order to reduce the impact of the material on the conveyor belt, the chute should be mined and the drop distance of the material is reduced. The conveying belt should shorten the spacing of the roller and use the cushion roller as the leaky material, and the conveyer belt should be flexible and appropriate, so as to avoid the gear plate to be perfect and scrape the conveyer belt. The surface of the belt.
3、防止输送带负荷启动。
3, prevent the load of conveyor belt starting.
4、输送带发生跑偏，应及时采取措施纠正。
4, belt deviation occurs, should take timely measures to correct.
5、不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
5, the conveyor belts of different types and specifications should not be used together, and the joints should be glued.
6、输送带的类型、结构、规格、层数应根据使用条件合理选用。
6, the type, structure, specification and number of layers should be selected according to the use conditions.
7、输送带运行速度一般不宜大于2.5m/s，块度大，磨损性大的物料和使用固定梨的卸料装置应尽量采用低速。
7, the conveyor belt generally should not run faster than 2.5m/s, large size, wear material and the use of fixed pear unloading device should be used as low as possible.
8、输送机在使用时，如有托辊缺少，应及时添加及修好；托辊被物料覆盖，造成回转不灵，防止漏料卡于滚筒与胶带之间，注意输送带活动部分的润滑，但不得油污输送带。
8, when the conveyor is used, if the roller is missing, it should be added and repaired in time; the roller is covered by the material, which causes no turning, prevents the leakage between the roller and the tape, and pays attention to the lubrication of the active part of the conveyer belt, but not the oil conveyer belt.
9、避免输送带遭受机架，支柱或块状物料的阻滞，防止碰破扯裂，发现输送带局部破损时，应用人造棉及时修补，以免扩大。
9, avoid the conveyor belt from the block, support or block material block, prevent breaking and tear, and find that when the conveyor belt is partially damaged, artificial cotton can be repaired in time so as not to expand.
