1、贮存时库房内温度宜保持在—15℃—+40℃之间，相对湿度宜保持在50—80%之间。

1, storage room temperature should be kept at 15 ℃, between + 40 ℃, relative humidity should be kept between 50-80%.

2、橡胶输送带在运送和贮存中，应保持清洁，防止阳光直射，雨雪浸淋，防止与酸 、碱、油类，有机溶剂等影 响橡胶质量的物质接触，并距离发热设备1米以外。

2, rubber conveyor belt in the transport and storage, should be kept clean, prevent direct sunlight, rain and snow shower, prevent with acid, alkali, oil, organic solvent such as impact the quality of rubber material, heating equipment and distance 1 metres away.

3、橡胶输送带工作速度不应大于5.0米/秒，运送块度大，磨损性大的物料和运用固定犁型卸料设备时应尽量选用低速。超出规矩速度时，会影响胶带运用寿命。

3, rubber conveyor belt work should not be more than 5.0 m/s speed, large transport blocks of abrasion resistant materials and using the fixed type plow discharge equipment should be as far as possible choose low speed. When you exceed the rules, it affects the application of tape.

4、贮存中橡胶输送带须成卷放置，不得折叠，放置时期应每季翻动一次。

In storage, rubber conveyor belt must be rolled into a roll, not folded, and should be turned once every season.

5、为减轻物料对胶带的冲击与磨损，给料方向应顺胶带的工作方向；物料下落到胶带上的落差应尽量减小；给料口应避开滚筒或托辊的正上方；胶带受料段应缩短托辊距离和采取缓冲方法。为防止 刮破胶带，挡料设备刮板打扫设备和卸料设备与胶带的接触 部分应选用硬度适合的橡胶板，不要选用夹有布层的胶带头。

In order to reduce the impact and wear of the material, the direction of the tape should be directed in the direction of the tape. The drop of material falling to the tape should be minimized. Feed the mouth to avoid the top of the roller or the roller. The tape section should shorten the distance of the roll and the buffer method. To prevent scraping the broken belt, keep-off device scraper cleaning equipment and unloading equipment and contact part of the tape should choose suitable rubber hardness, don't choose with layers of plastic to take the lead.

6、运送机的传动滚筒直径与输送带布层的联络，传动滚筒改向滚筒的配套以及对托辊槽角的恳求，应根据输送机的规划规矩，合理挑选。

6, transporter transmission roller conveyor belt layers and the diameter of contact and transmission drum redirection roller and a request for roller groove Angle, should be based on the planning of the conveyor line, reasonable selection.

7、防止胶带遭受机架、支柱或块状物料的阻滞，防止碰破扯裂。

To prevent the tape from being held up by the frame, pillar, or block material, preventing the tear from breaking.

8、在运用过程中防止托辊被被物料掩盖，构成回转不灵，防止漏料卡于滚筒与胶带之间 ，留心活动有些的润滑，但不得油污输送带。

8, in the process of applying to prevent roller has been masked by material, a rotary is ineffective, prevent leakage of material between the roller and the tape, pay attention to some lubrication, but not greasy dirt conveyor belt.